FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
- 10. Suspension brackets
   - 10.1. A forward suspension bracket
      10.1.1. A technical characteristics
      + 10.1.2. Service and repair
   + 10.2. A back suspension bracket
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


59ff046c



10. Suspension brackets

10.1. A forward suspension bracket

10.1.1. A technical characteristics
THE GENERAL DATA

Forward suspension bracket independent, type Mac Pherson. Consists of two racks of the suspension bracket, two bottom cross-section levers and the cross-section stabilizer which ends also carry out a role of jet levers. Each rack contains a screw spring, coaxial with the telescopic shock-absorber.

The convergence is a distance between a forward and back part of forward wheels. This corner usually positive as from round the corner an inclination of a wheel (disorder) and resistance качению wheels aspire to be developed outside.

The angle of slope of a wheel and longitudinal angle of slope of an axis of turn reduce transfer of blows and vibration from roughnesses of road by a steering. The wheel angle of slope is a corner on which the wheel deviates a vertical plane. The longitudinal angle of slope of an axis of turn is a corner on which the rack of a forward suspension bracket is inclined that essential impact at movement on a straight line makes.

Shock-absorbers

Shock-absorbers hydraulic telescopic bilateral action also make the bottom part of racks of a suspension bracket.

Mark: Motorcraft.

The stabilizer

The cross-section stabilizer is connected in an average part to a body by means of two plugs. Stabilizer shoulders are connected to the bottom cross-section levers of a suspension bracket with the help самоконтрящихся nuts.

Diameter of the lever of the stabilizer: 27 mm.

Naves of forward wheels

Each nave is located on two conic bearings established with a tightness.

The tightening moments

The top fastening of a rack of a suspension bracket to a body
40 – 52 Nanometers
The bottom fastening of a rack of a suspension bracket to a rotary fist
80 – 90 Nanometers
Spherical finger of the lever to a rotary fist of a wheel
65 – 85 Nanometers
Fastening of the hinge of the lever to an engine mount cross-beam:
  – 1st stage
45 Nanometers
  – 2nd stage
To weaken and tighten 15 Nanometers
  – 3rd stage
To tighten on 90 °
Stabilizer fastening to a body
70 – 90 Nanometers
Stabilizer fastening to levers
70 – 110 Nanometers
Fastening of a cross-beam of an engine mount to a body
70 – 90 Nanometers
The spherical hinge of steering bent for to a rotary fist
25 – 30 Nanometers
Nut of a nave of a wheel
390 – 450 Nanometers
Nut of fastening of a wheel
100 Nanometers

Installation of forward wheels

Model and year of release
Suspension bracket type
Parametres
Convergence (mm)
Longitudinal angle of slope of an axis of turn
Wheel angle of slope
Without adjustment of a road clearance till January 1992
The standard
Rating value 2,0 ± 1 mm or 0°20 ' ± 10'
1°51 ' ± 1 °
-0°23 ' ± 1 °
With adjustment of a road clearance till January 1992
The standard
1°58 ' ± 1 °
-0°23 ' ± 1 °
Without adjustment of a road clearance till January 1992
The strengthened
1°46 ' ± 1 °
0°00 ' ± 1 °
Engine DOCH, usual variant since February 1992
The standard
2°27 ' ± 1 °
-0°17 ' ± 1 °
Engine DOCH, the improved variant since February 1992
The standard
2°26 ' ± 1 °
-0°17 ' ± 1 °
Engine V6 of 2,4 l, a usual variant since February 1992
The standard
2°17 ' ± 1 °
-0°27 ' ± 1 °
Engine V6 of 2,4 l, the improved variant since February 1992
The standard
2°50 ' ± 1 °
-0°21 ' ± 1 °
Engine V6 of 2,9 l since February 1992
The standard
2°22 ' ± 1 °
-0°21 ' ± 1 °
The diesel engine, usual variant since February 1992
The standard
2°35 ' ± 1 °
-0°10 ' ± 1 °
The diesel engine, the improved variant since February 1992
The standard
2°25 ' ± 1 °
-0°23 ' ± 1 °
The engine of 2,9 l 24V
The standard
2°21 ' ± 1 °
-0°28 ' ± 1 °
With adjustment of a road clearance till January 1992
The standard
2°27 ' ± 1 °
-0°20 ' ± 1 °
All-wheel drive models
The standard
3°11 ' ± 1 °
0°00 ' ± 1 °