FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
- 8. A kardannyj shaft and the back bridge
   8.1. A technical characteristics
   - 8.2. A kardannyj shaft
      8.2.1. Removal and installation
      8.2.2. Repair of the intermediate bearing
   + 8.3. The back bridge
   + 8.4. Power shafts
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


59ff046c



8.2. A kardannyj shaft

8.2.1. Removal and installation
THE GENERAL DATA

Rubber муфта карданного shaft GAF 30

1 – metal муфта,

2 – rubber демпферы,

3 – a rubber covering

Rubber муфта карданного shaft GAF 41

1 – connection nuts муфты with демпфером,

2 – муфта GAF,

3 – демпфер,

4 – nuts of connection a shaft-mufta

Removal of the intermediate bearing

1 – a lock ring,
2 – a bolt,
3 – the intermediate bearing,
4 – the case of the intermediate bearing,
5 – the crosswise hinge,
6 – an adjusting U-shaped plate

Removal of the intermediate bearing by means of a stripper


PERFORMANCE ORDER
1. To establish the car over the viewing channel or on the lift.
2. To designate mutual position of the crosswise hinge and a flange of a gear wheel of the main transfer and to disconnect карданный a shaft from the back bridge (bolts of fastening of a back flange are specified by arrows). To unscrew the case of the intermediate bearing, having designated position of linings between the case of the bearing and a car body (these designations will be useful at installation карданного a shaft and its intermediate bearing).
3. To disconnect карданный a shaft from a transmission, paying attention not to damage a sealing ring in a back part картера. After extraction of a shaft the aperture in a back part картера should be muffled transmissions a stopper or a forward tip faulty карданного a shaft not to admit вытекания some oil from a transmission.

Installation

PERFORMANCE ORDER
1. From an aperture of a back part картера transmissions to take a stopper. To check up installation of a sealing ring of a back part картера transmissions and to insert into it the forward end карданного a shaft, paying attention not to damage an edge of a sealing ring.
2. To establish the intermediate bearing карданного a shaft, having arranged under it corresponding linings according to the designations put during dismantling (without tightening fastening bolts).
3. To connect карданный a shaft to a flange of a leading gear wheel of the main transfer according to the designations of a relative positioning put earlier. To establish the new linings protecting bolts from unscrewing.
4. Rotating карданный a shaft to establish the intermediate bearing and to tighten fastening bolts the corresponding moment.
5. To check up and in case of need to add quantity of oil in a transmission.

TRANSMISSION OF TYPE МТ 75

Difference карданного a shaft applied with a transmission of type МТ 75, consists in fastening карданного a shaft to a transmission.

PERFORMANCE ORDER
To unscrew three nuts of fastening rubber муфты карданного a shaft to a target shaft of a transmission and to remove карданный a shaft. Two types rubber муфты GAF 30 or GAF 41 are applied.

МУФТА GAF 30

Fastening hairpins муфты should not be turned at the appendix of the moment of 80 Nanometers. In a case if a hairpin проворачиватся at the appendix of the smaller moment, she is necessary for unscrewing and establishing as follows.

PERFORMANCE ORDER
1. To clear a carving in a transmission flange.
2. To put on a carving of apertures two drops of means against unscrewing (from two parties of an aperture), immediately to screw up a hairpin and within 30 minutes to give the chance to means to harden.
3. To check up a condition rubber муфты on presence of mechanical damages and cracks. In the presence of cracks карданный the shaft is subject to replacement as карданный the shaft is balanced with муфтой as a single whole. At replacement карданного a shaft to establish a shaft with муфтой GAF 41.
4. To fix муфту to a transmission, using new nuts.

МУФТА GAF 41

Unscrewing, check and installation are made in the same way, as for муфты GAF 30, besides, that hairpins should not be turned at the appendix of the moment of 110 Nanometers.