FORD SCORPIO

1985-1994 of release

Repair and car operation

14.9.2. Dismantling and starter assemblage

THE GENERAL DATA

Starter Bosch

1 – the case of the electromagnetic actuator, 2 – a spring, 3 – an anchor of the electromagnetic actuator, 4 – the lever, 5 – a rubber insert, 6 – a cover, 7 – the screw of fastening electromagnetic The actuator, 8 – a lock ring, 9 – a ring, 10 – an anchor of a starter,

11 – the case of a starter, 12 – windings, 13 – the block of brushes of a collector, 14 – a cover of a collector, 15 – a sealing ring, 16 – a washer, 17 – a lock ring, 18 – a protective cover, 19 – a bolt of fastening of a protective cover, 20 – a coupling bolt of a starter

The block of brushes of a collector of starter Bosch

1 – external contact, 2 – the plug

Starter Bosch GF

1 electromagnetic actuator, 2 – a lining, 3 – a cover, 4 – contacts, 5 – the screw, 6 – a protective cover, 7 – a sealing ring, 8 – a lock ring, 9 – a washer, 10 – the plug, 11 – a cover of a collector, 12 – the holder of brushes of a collector, 13 – a winding conclusion статора, 14 – the case of a starter,

15 – a forward cover, 16 – the screw, 17 – the plug, 18 – an axial bolt of the lever, 19 – the lever, 20 – a coupling bolt of a starter, 21 – a spring of a clip of a brush, 22 – a brush, 23 – a collector, 24 – an anchor of a starter, 25 – приводная a gear wheel with обгонной муфтой, 26 – a ring, 27 – a lock ring

Starter Bosch DW with a reducer

1 electromagnetic actuator, 2 – a spring, 3 – an anchor of the electromagnetic actuator, 4 – the lever, 5 – a forward cover, 6 – приводная a gear wheel with обгонной муфтой, 7 – a lining, 8 – an external gear wheel of a reducer, 9 – a power shaft with planetary Gear wheels, 10 – a lock ring,

11 – a coupling bolt of a starter, 12 – a protective cover, 13 – a lock ring, 14 – a ring, 15 – a plate, 16 – the holder of brushes of a collector, 17 – the case of a starter, 18 – a rubber lining, 19 – an anchor of a starter, 20 – a cover

Starters Lucas

1 – a head, 2 – knot of a drive, 3 – the lever of a drive, 4 – the electromagnetic switch,

5 – статор, 6 – a rotor, 7 – a back cover with щеткодержателем

Starter Cajavec

1 – a head, 2 – knot of a drive, 3 – the lever of a drive, 4 – the electromagnetic switch,

5 – статор, 6 – a rotor, 7 – щеткодержатель

Starter Nippondenso

1 – a head, 2 – knot of a drive, 3 – the lever of a drive, 4 – the electromagnetic switch,

5 – статор, 6 – a rotor, 7 – щеткодержатель

After starter dismantling it is necessary to check up:

  – A condition of brushes, their deterioration, and also freedom of moving of brushes in щеткодержателях;
  – Force of a clip and position of springs of brushes;
  – A kind of a collector which should be cleared a rag moistened in gasoline or трихлорэтилене, and прошлифовать a fine-grained emery paper;
  – A condition of plugs of self-greased bearings; in case of need replacements should be lowered new plugs not less than for 20 minutes in engine oil (viscosity SAE 30 or 40) before their installation in a starter.

Check of the electromagnetic actuator

PERFORMANCE ORDER

1. To disconnect a wire of weight from the accumulator and all wires from the electromagnetic actuator. 2. To connect the accumulator with consistently included control bulb capacity of 3 Vt to the case and a socket of a food of a winding of the electromagnetic actuator (1 – carving contact for connection of a wire from the accumulator, 2 – carving contact to the starter electric motor, 3 – a socket of a food of a winding electromagnetic The actuator). 3. In the absence of breakage of a winding the bulb should burn. 4. For check of contacts of inclusion of a starter to connect the accumulator with consistently included control bulb capacity of 12-21 Vt to carving contacts of the electromagnetic actuator and an additional wire to a socket of a food of a winding of the electromagnetic actuator (1 – carving contact for connection of a wire from the accumulator, 2 – carving contact to the starter electric motor, 3 – a socket of a food of a winding of the electromagnetic actuator). 5. At connection of an additional wire to a socket of a food of a winding of the electromagnetic actuator should work the electromagnetic actuator and light up a bulb.