Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
- 7. Transmissions
+ 7.1. A mechanical five-speed transmission of type
- 7.2. A mechanical transmission of type МТ 75
7.2.1. A technical characteristics
+ 7.2.2. Service and repair
+ 7.3. Automatic transmission А4LD
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment
7.2. A mechanical transmission of type МТ 75
7.2.1. A technical characteristics
| THE GENERAL DATA |
The transmission three-total, a classical design, has five synchronised transfers for advance (4 transfer – a straight line) and the synchronised transfer of a backing. The box is established along a car axis behind the engine. The gear change lever is established on a car floor. It is established on cars since October, 1988.
The basic distinctions in comparison with a type transmission
| The maximum moment on an input |
300 Nanometers
|
| Method of consolidation of planes картера |
By means of special герметизирующей pastes
|
Gear wheels are established on needle bearings.
The reverse gear is synchronised.
Internal directing the gear change lever has protection against casual inclusion of transfer of a backing.
Transfer numbers
CARS WITH ENGINES NRA AND N9B
|
Transfer
|
Transfer number of transfer
|
Transfer number of the main transfer
|
Full transfer number
|
|
1
|
3,89
|
3,92
|
15,248
|
|
2
|
2,08
|
8,153
| |
|
3
|
1,34
|
5,252
| |
|
4
|
1,00
|
3,920
| |
|
5
|
0,82
|
3,214
| |
|
Backing
|
3,51
|
13,759
|
CARS WITH ENGINES N8B
|
Transfer
|
Transfer number of transfer
|
Transfer number of the main transfer
|
Full transfer number
|
|
1
|
3,89
|
3,14
|
12,21
|
|
2
|
2,08
|
6,53
| |
|
3
|
1,34
|
4,20
| |
|
4
|
1,00
|
3,14
| |
|
5
|
0,82
|
2,57
| |
|
Backing
|
3,51
|
11,02
|
Greasing
| Quantity of oil |
1,20 дм3
|
| Type |
Oil for transmissions Ford ЕSD M2C 186 A
|
| Periodicity of service |
Level check each 20 000 km or once a year; periodic replacement of oil is not provided
|
The tightening moments
| Carter of the block of gear wheels to картеру couplings |
20 – 27 Nanometers
|
| Carter of coupling to the block of cylinders of the engine |
29 – 41 Nanometers
|
| Fastening of the directing plug выжимного the coupling bearing |
15 – 17 Nanometers
|
| Holder of the bearing of an intermediate shaft: | |
| – 1 stage |
15 – 20 Nanometers
|
| – 2 stage |
To weaken on 60 °
|
| Fastening of a nut of the bearing |
9 – 11 Nanometers
|
| Fastening of an axis of transfer of a backing to картеру |
8 – 11 Nanometers
|
| Bolt of a stopper of transfer of a backing to картеру transmissions |
18 – 25 Nanometers
|
| Nut of an intermediate shaft |
200 Nanometers
|
| Stopper of a stopper of the selector |
20 – 27 Nanometers
|
| Stopper of an aperture of filling and oil plum |
23 – 32 Nanometers
|
| Fastening of a lock ring of the ball bearing of a secondary shaft |
20 – 27 Nanometers
|
| The switch of lanterns of a backing |
10 – 14 Nanometers
|