FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
- 14. An electric equipment
   14.1. A technical characteristics
   14.2. Safety locks and the relay
   14.3. Electronic blocks of management
   14.4. System of the central blocking
   14.5. System of indexes of turns
   14.6. The fuel computer
   14.7. Additional control system
   - 14.8. The generator
      14.8.1. Removal and generator installation
      14.8.2. Dismantling and generator assemblage
      14.8.3. Replacement of brushes of the generator and a pressure regulator
      14.8.4. The basic malfunctions of the generator
      14.8.5. Tension adjustment клинового a belt
   + 14.9. A starter
   + 14.10. A windscreen screen wiper, knot of indexes and a headlight
   14.11. Removal and installation of a combination of devices
   14.12. External and internal illumination
   + 14.13. An other electric equipment
   + 14.14. Electroschemes


59ff046c



14.8.3. Replacement of brushes of the generator and a pressure regulator
THE GENERAL DATA

Replacement of a regulator of pressure and generator brushes can be made, without removing the generator from the engine.

It is possible to make separate removal of brushes and a regulator.

GENERATOR BOSCH

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. To unscrew 3 bolts and to remove the heat-shielding screen.
3. To unscrew 2 screws of fastening of a regulator of pressure and, being careful, to take a regulator.
4. To check up length of graphite brushes (distance) which should be not less than 5 mm.
5. For replacement of coal brushes it is necessary отпаять токоподводы, to take the worn out brushes and springs, to establish new brushes with springs in a nest of a regulator and to solder токоподвод so that length of brushes made 10 mm. At a ration not to suppose gumboil and solder hit on токоподвод, except a soldering place (1 – brushes, 2 – springs of a clip of brushes, 3 – the holder of brushes).
6. To check up ease of moving of brushes in the holder.

GENERATOR LUCAS

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. To remove the heat-shielding screen.
3. To remove a socket with wires from the generator.
4. To unscrew a back cover of the generator.
5. To disconnect wires from a regulator, to unscrew a connecting plate, the fixing screw of a regulator and to take a regulator (1 – the screw, 2 – a plastic lining, 3 – a connecting plate, 4 – a regulator).
6. To unscrew screws (fastenings of graphite brushes are specified by an arrow) and to take brushes from the holder.
7. To check up length of graphite brushes which should be not less than 5 mm.

GENERATOR MOTOROLA

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. To remove the heat-shielding screen.
3. To remove a socket with wires from the generator.
4. To unscrew a regulator () and to disconnect 2 wires (are specified by arrows).
5. To unscrew the fastening screw щеткодержателя.
6. To unscrew щеткодержатель and, cautiously turning it outside, to take from the generator (1 – a graphite brush, 2 – contact).
7. To check up length of graphite brushes which should be not less than 4 mm.