FORD SCORPIO

1985-1994 of release

Repair and car operation

7.2.2.2. Transmission dismantling

THE GENERAL DATA

Carter of a transmission

1 – картер couplings, 2 – картер transmissions, 3 – a stopper of pouring of oil, 4 – a stopper plum of oil, 5 – the directing plug выжимного the bearing,

6 – a support of the bearing of an intermediate shaft, 7 – the switch of lanterns of a backing, 8 – сапун, 9 – details of a drive of a speedometer, 10 – a flange of a target shaft of a transmission

The mechanism of a gear change, transmission of type МТ 75

1 – an axis of plugs of 3-4 transfers, 5th transfer and transfer of a backing, 2 – an axis of plugs of 1-2 transfers, 3 – plugs of 3-4 transfers, 4 – plugs of 5th transfer and transfer of a backing, 5 – plugs, 6 – plugs of 1-2 transfers, 7 and 8 – selectors,

9 – a stopper of blocking, 10 – a pin, 11 – a pin, 12 – a finger of management, 13 – the plug of management, 14 – the finger of blocking doing impossible simultaneous inclusion of two transfers, 15 – plates

The front view картера couplings

1 – a plate of fixing of a nut, 2 – a nut of the bearing of an intermediate shaft

Removal of the directing plug выжимного the coupling bearing

1 – special adaptation Ford 16.040

Kind of a left-hand side of a transmission

1 – a bolt of a stopper of transfer of a backing, 2 – a stopper of a stopper of the selector, 3 – the switch of fires of a backing, 4 – a forward bolt of fastening of an axis of an intermediate gear wheel of transfer of a backing, 5 – a back bolt of fastening of an axis of an intermediate gear wheel of transfer of a backing

Removal of a flange of a secondary shaft by means of a stripper

---

The prevention

After transmission dismantling it is necessary to replace all spring lock rings on new with the thickness providing reception of demanded values of an axial backlash of elements established with their help. It is necessary to replace all sealing rings also.

---

Transmission elements (shaft, bearings, synchronizers, the gear change mechanism etc.) settle down in two informed among themselves картерах. The first of them, located more close to the engine, contains also coupling and is called картером couplings (though in its back part six elements of a transmission settle down); another is called картером transmissions (though it does not contain all elements of this knot).

PERFORMANCE ORDER

1. To merge oil from a transmission. 2. With картера couplings to remove выжимной the bearing and plugs of deenergizing of coupling. 3. To fix a flange of connection of the forward hinge карданного a shaft and to unscrew a nut of fastening of a flange by means of drawing of easy blows on a key (1 – the adaptation for flange blocking, 2 – a hinge flange). 4. By means of adaptation Ford 16.040 to remove directing plug выжимного the coupling bearing. 5. To remove an internal spring ring from a primary shaft. 6. To remove a plate of fixing of a nut of the bearing of an intermediate shaft (fig. the Front view картера couplings see). 7. By means of a key of 17 mm to unscrew a nut of the bearing of an intermediate shaft. 8. Sideways картера to unscrew bolts (type Torx) stopper of transfer of a backing (fig. the Kind of a left-hand side of a transmission see). 9. Sideways картера to unscrew a stopper (2) stoppers of the selector and to take a spring, a pusher, the plug and a ball of a stopper of the selector. 10. To unscrew the switch (3) fires of a backing. 11. To unscrew two bolts (4 and 5) fastenings of an axis of an intermediate gear wheel of transfer of a backing and to take only a forward bolt (4). 12. To unscrew ten bolts of connection картера couplings with картером transmissions. 13. By means of two screw-drivers cautiously to divide both parts картера transmissions. 14. To remove картер couplings with картера transmissions; in case of need to use the adaptation 16.041. 15. To remove an axis of plugs (1) (fig. the Mechanism of a gear change, a transmission of type МТ 75 see) 3–4 transfers, 5th transfer and backing transfer. 16. To take a back bolt (5) (fig. the Kind of a left-hand side of a transmission see) fastenings of an axis of an intermediate gear wheel of transfer of a backing. 17. From картера transmissions to take a magnet. 18. By means of a corresponding stripper to remove from a secondary shaft a flange of connection of the forward hinge карданного a shaft (fig. Removal of a flange of a secondary shaft by means of a stripper see). 19. To take a sealing ring from a secondary shaft. 20. To remove приводную a gear wheel of a speedometer and the remote plug. 21. To extend from картера transmissions a secondary shaft by means of a stripper.