FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   + 3.3. Engine V6
   + 3.4. Ignition and engine management systems
   - 3.5. Diesel engines
      3.5.1. A technical characteristics
      3.5.2. The repair which is not demanding removal of the engine
      3.5.3. Check and adjustment of backlashes of valves
      + 3.5.4. Fuel system
      - 3.5.5. A head of the block of cylinders
         3.5.5.1. Removal of a head of the block of cylinders
         3.5.5.2. Installation of a head of the block of cylinders
         3.5.5.3. Check and repair of a head of the block of cylinders
      3.5.6. Removal and engine installation
      + 3.5.7. Dismantling, repair and engine assemblage
      3.5.8. Турбокомпрессор
      + 3.5.9. Greasing system
      + 3.5.10. Cooling system
      3.5.11. Typical malfunctions of the engine
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


59ff046c



3.5.5. A head of the block of cylinders

3.5.5.1. Removal of a head of the block of cylinders
THE GENERAL DATA

Knot of a head of the block of cylinders

1 – a head of the block of cylinders,
2 – a lining of a head,
3 – the vortical chamber of combustion,
4 – a fixing ball,
5 – a nest of the final valve,
6 – a nest of the inlet valve,
7 – directing valves,
8 – a cover of a head of the block of cylinders,
9 – a lining of a cover of a head,
10 – a stopper маслозаливной mouths,
11 – the target pipeline of a cooling liquid,
12 – the gauge of temperature of a cooling liquid,
13 – the thermostat of the automatic device of start of the cold engine,
14 – the thermostat case

The prevention

At removal of a head of the block of cylinders the engine should be cold (it is necessary to wait for 6 hours after engine deenergizing).


PERFORMANCE ORDER
1. To disconnect from the accumulator a wire of weight and to remove the air filter.
2. To remove a sheet casing from below the engine, to merge cooling liquid (having substituted the corresponding capacity). To disconnect hoses of system of cooling: bottom from a radiator and top from the pump.
3. To disconnect the pipeline from a broad tank of system of cooling, from a head of the block of cylinders, from a heating system of salon and the vacuum pipeline from the vacuum pump.
4. To disconnect a wire and токовую the tyre from candles накаливания, and also other electric wires.
5. To disconnect a cable of adjustment of idling from a head of the block of cylinders of the engine.
6. To disconnect the pipeline of injection of fuel and return pipelines from atomizers, to unscrew atomizers and candles накаливания from a head of the block of cylinders.
7. To remove the vacuum pump together with приводным клиновым a belt and to remove the generator.
8. To disconnect a frame of fastening of the generator from an inlet collector and to remove клиновой a belt.
9. To disconnect from a head of the block of cylinders the pipeline of giving of oil and a forward exhaust pipe from a final collector.
10. To uncover heads of the block of cylinders and an axis of levers of valves.
11. To take cores of pushers.
12. To unscrew bolts of fastening of a head of the block of cylinders in sequence, return sequence of their tightening (fig. Sequence of a tightening of bolts of fastening of a head of the block of cylinders see).
13. To remove a head of the block of cylinders together with collectors: inlet and final. To remove a head lining.