FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   - 3.1. Engine OHC
      3.1.1. A technical characteristics
      - 3.1.2. Service and repair
         3.1.2.1. Engine adjustment
         - 3.1.2.2. The repair which is not demanding removal of the engine
            3.1.2.2.1. Removal and installation of a gear belt
            3.1.2.2.2. Removal of a head of the block of cylinders
            3.1.2.2.3. Dismantling and assemblage of a head of the block of cylinders
            3.1.2.2.4. Installation of a head of the block of cylinders
            3.1.2.2.5. Removal and installation of the oil pallet
            3.1.2.2.6. Replacement of a forward sealing ring of a cranked shaft
            3.1.2.2.7. Replacement of a back sealing ring of a cranked shaft
            3.1.2.2.8. Replacement of support of the engine
         3.1.2.3. Removal and engine installation
         + 3.1.2.4. Engine repair
         3.1.2.5. Greasing system
         3.1.2.6. Ventilation system картера
   + 3.2. Engine DOHC
   + 3.3. Engine V6
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


59ff046c



3.1.2.2.2. Removal of a head of the block of cylinders
THE GENERAL DATA

Knot of a head of the block of cylinders

1 – a cover of a head of the block of cylinders,
2 – clamping plates,
3 – a lining of a cover,
4 – a camshaft,
5 – an adjusting plate of a camshaft,
6 – a bolt of fastening of a head,
7 – a spring of the lever of the valve,
8 – the lever of the valve,
9 – a bolt with a spherical tip (a support of the lever of the valve),
10 – crackers,
11 – a plate of a spring,
12 – the directing plug,
14 – the valve,
15 – plugs of bearings of a camshaft,
16 – the pipeline of giving of oil to bearings of a camshaft,
17 – a lining of a head of the block of cylinders,
18 – a head of the block of cylinders,
19 – a sealing ring of a camshaft

Knot of the air filter


1 – the case,

2 – a cover,

3 – a filtering element,

4 – the goffered hose of an air inlet,

5 – an air inlet of warm air

PERFORMANCE ORDER
1. To disconnect from the accumulator a weight wire.
2. To merge cooling liquid from cooling system.
3. To remove the air filter, to disconnect pipelines and draughts from the carburettor and an inlet collector.
4. To disconnect electric wires from the carburettor and a head of the block of cylinders.
5. To disconnect from spark plugs of a wire of a high voltage and to remove the high voltage distributor.
6. To disconnect pipelines of a cooling liquid from the chamber of the starting arrangement of the carburettor, the top hose from a radiator, and also a hose of a broad tank from a head of the block of cylinders.
7. To disconnect a reception exhaust pipe from a final collector (3 nuts).
8. To remove a protective casing of a gear belt of system газораспределения (3 bolts), and also a cover of a head of the block of cylinders (10 bolts) together with its sealant.
9. To establish the piston of 1 cylinder in the top dead point, turning a cranked shaft for a bolt, крепящий a pulley клинового a belt, in a direction of working rotation until the label of the top dead point will not be combined with a label on a casing of a forward sealing ring of a cranked shaft, and the label on a cam-shaft pulley will not be combined with a label on a head of the block of cylinders. To note position of a rotor of the distributor in relation to the distributor case for what to uncover the distributor having raised a screw-driver 2 lateral fixing скобы and having unscrewed 2 screws of fastening of a cover.
10. To unscrew fastening of the tension device of a gear belt of system газораспределения (the adaptation 21.012) to weaken it and to tighten in this position.
11. To remove a gear belt of system газораспределения.
12. To unscrew spark plugs, and also to unscrew bolts of a head of the block of cylinders (the adaptation 21.002) in sequence opposite to their tightening.
13. To remove a head of the block of cylinders from the block of cylinders of the engine.

The prevention

It is not necessary to have a head of the block of cylinders the bottom plane on a horizontal surface as it threatens with damage of valves acting below a plane. A head of the block of cylinders it is necessary to have on two wooden брусках so that plates of valves concerned nothing.