FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   - 3.2. Engine DOHC
      3.2.1. A technical characteristics
      - 3.2.2. The repair which is not demanding removal of the engine
         3.2.2.1. A chain газораспределительного the mechanism and asterisks
         - 3.2.2.2. A head of the block of cylinders
            3.2.2.2.1. Removal of a head of the block of cylinders
            3.2.2.2.2. Dismantling and assemblage of a head of the block of cylinders
            3.2.2.2.3. Check of a head of the block of cylinders
            3.2.2.2.4. Check of directing plugs of valves
            3.2.2.2.5. Processing of saddles of valves in a head of the block of cylinders
            3.2.2.2.6. Grinding in
            3.2.2.2.7. Assemblage of a head of the block of cylinders
            3.2.2.2.8. Installation of a head of the block of cylinders
         3.2.2.3. Removal and installation of a back sealing ring of a cranked shaft
      + 3.2.3. Removal and installation of the engine without a transmission
      3.2.4. Ventilation system картера
      + 3.2.5. Greasing system
   + 3.3. Engine V6
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


59ff046c



3.2.2.2.8. Installation of a head of the block of cylinders
THE GENERAL DATA

Sequence of a tightening of bolts of a head of the block of cylinders of engine DOHC

Bolts М11 – sequence of a tightening: 1–10.

Bolts М8 – sequence of a tightening: 11–13.

Arrangement of covers of bearings of camshafts


PERFORMANCE ORDER
1. Carefully to clear interfaced surfaces of a head of the block of cylinders and the block of cylinders.
2. To establish on the block of cylinders a new lining.
3. To turn a cranked shaft so that pistons were established in the middle of the course.
4. To establish a head of the block of cylinders on the block of cylinders.
5. To grease with a thin layer of engine oil a carving of bolts of fastening of a head of the block of cylinders (arrows bolts М8 of fastening of a forward part of a head of the block of cylinders are shown), to establish them into place and to tighten the demanded moment in certain sequence (subsection 3.2.1 see).
6. To grease with a thin layer of engine oil of a support of camshafts in a head and to establish into place camshafts.
7. To grease with a thin layer of engine oil of a cover of bearings of camshafts and to establish them into place according to marks. Covers of bearings of a camshaft operating inlet valves have marks R1–R5, and covers of bearings of a camshaft operating final valves have marks L1–L5. Numbering of covers from outside a mechanism drive газораспределения.
8. To establish the pipeline of giving of oil to cams of camshafts.
9. Gradually and consistently to tighten nuts of fastening of covers of fastening of camshafts in certain sequence. By hand to tighten fastening nuts, turning them it is consecutive on 180 ° before contact of a cover with a head of the block of cylinders. Sequence of a tightening: L1 and R1, L5 and R5, L3 and R3. Then to screw up by hand other nuts of fastening of covers.
10. To tighten nuts of fastening of covers the demanded moment, turning them on the same corner in the following sequence: L1 and R1, L5 and R5, L3 and R3, L2 and L4, R2 and R4.
11. To establish a chain газораспределительного the mechanism and an asterisk (subsection 3.2.2.1 see).
12. To establish a cover of a head of the block of cylinders with a new lining and to tighten bolts of fastening of a cover consistently from edge to the centre.
13. To screw in spark plugs.
14. To establish the ignition distributor, a rotor of the distributor and a cover.
15. To establish into place high-voltage wires.
16. To screw on a final collector a reception exhaust pipe with a new lining.
17. To connect wires to the radiator fan.
18. On cars with system of injection of fuel to connect a plait of wires to the engine and топливопроводы to a pressure regulator.
19. To connect vacuum hoses and an accelerator cable.
20. To connect a hose of system of ventilation картера the engine to a head of the block of cylinders.
21. To connect a hose of giving of a cooling liquid to a branch pipe on a head of the block of cylinders.
22. To connect a hose of a radiator and a broad tank.
23. To establish the air filter.
24. To fill in engine oil in the engine.
25. To fill in cooling liquid in cooling system.
26. To connect a weight wire to the accumulator.
27. To start the engine and if necessary to adjust.