FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
- 7. Transmissions
   + 7.1. A mechanical five-speed transmission of type
   + 7.2. A mechanical transmission of type МТ 75
   - 7.3. Automatic transmission А4LD
      7.3.1. A technical characteristics
      - 7.3.2. Service and repair
         7.3.2.1. The work description
         7.3.2.2. Check of level of oil in a transmission
         7.3.2.3. Check and washing of a hydrokinetic transmission
         7.3.2.4. Check of pressure of oil in a transmission operating time
         7.3.2.5. Test of an overload of the engine by hydrokinetic transfer
         7.3.2.6. Adjustment of a tape of a brake of forward planetary transfer
         7.3.2.7. Removal and installation of a vacuum regulator
         7.3.2.8. The hydraulic booster of back planetary transfer
         7.3.2.9. A centrifugal regulator of pressure of oil
         7.3.2.10. Replacement of a back sealing ring
         7.3.2.11. Removal and installation of the mechanism of a choice of transfers
         7.3.2.12. Removal and installation of draught of a choice of transfers
         - 7.3.2.13. Adjustment of a cable of mechanism Kick-down
            7.3.2.13.1. Cars with the electromagnetic valve
         7.3.2.14. Removal and transmission installation
         7.3.2.15. Malfunctions of an automatic transmission
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


59ff046c



7.3.2.13. Adjustment of a cable of mechanism Kick-down
THE GENERAL DATA

The sizes of a template for adjustment of a cable of the mechanism kick-down


Adjustment of a cable of the mechanism kick-down in 1st version of execution

And – a nut of adjustment of a tension of a cable of the mechanism kick-down,

In – a counternut,

With – a nut of adjustment of a tension of a cable of a pedal of an accelerator,

D – a cover of a cable,

Х = 8 mm – the control size

PERFORMANCE ORDER
1. To weaken a nut () adjustments of a tension of a cable of the mechanism kick-down and its counternut ().
2. To move a nut and a counternut till the end of a carving.
3. To press against the stop a pedal of an accelerator and to fix it in this position.
4. To turn a nut () adjustments of a tension of a cable of a pedal of an accelerator before reception of the size Х = 10 mm. For check of the size () template use according to fig. the Sizes of a template for adjustment of a cable of the mechanism kick-down is recommended.
5. In the course of nut turn () (fig. Adjustment of a cable of the mechanism kick-down in 1st version of execution see) опертая on it the spring and the plug cannot turn, as it would cause change of the size () during car movement.
6. After adjustment to take a template.
7. Between elements, for which the size is defined (), to place second party of a template according to fig. Sizes of a template for adjustment of a cable of the mechanism kick-down (width 8 mm) and to release an accelerator pedal. The template should remain clamped by these elements.
8. To pull a hand a cover (D) a mechanism cable kick-down in a direction shown by an arrow on fig. Adjustment of a cable of the mechanism kick-down in 1st version of execution to eliminate люфт a cable and to adhere a cover in this position.
9. To screw up an adjusting nut () to its emphasis about a casing plate and then to tighten its counternut ().