FORD SCORPIO

1985-1994 of release

Repair and car operation


Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      - 3.3.4. Dismantling and check of details of the engine
         3.3.4.1. Engine dismantling
         3.3.4.2. Check of degree of deterioration of details of the engine
         3.3.4.3. Axis knot коромысел
         3.3.4.4. Pushers of valves and a bar of pushers
         3.3.4.5. A camshaft
         3.3.4.6. Heads of the block of cylinders
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and piston rings
         3.3.4.9. Piston fingers and rods
         3.3.4.10. A cranked shaft
         3.3.4.11. Radical and шатунные bearings
         3.3.4.12. Distributive gear wheels
         3.3.4.13. A flywheel
         + 3.3.4.14. Greasing system
         3.3.4.15. Ventilation system картера
         - 3.3.4.16. Engine assemblage
            3.3.4.16.1. Installation of a cranked shaft
            3.3.4.16.2. Camshaft installation
            3.3.4.16.3. Installation of pistons and rods
            3.3.4.16.4. Installation of the oil pump
            3.3.4.16.5. Flywheel installation
            3.3.4.16.6. Installation of a gear wheel and a cover of a drive of the distributive mechanism
            3.3.4.16.7. Installation of the oil pallet, the water pump and a pulley коленвала
            3.3.4.16.8. Removal and installation of the oil heat exchanger
            3.3.4.16.9. Heads of the block of cylinders, axes коромысел and an inlet collector
         3.3.4.17. Adjustment of backlashes of valves
         3.3.4.18. Auxiliary details of the engine
         3.3.4.19. Engine installation
         3.3.4.20. Start of the engine after major repairs or restoration
      + 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


59ff046c На http://spetsmedpribor.net офтальмомиотренажер релаксатор.


3.3.4.16.2. Camshaft installation
THE GENERAL DATA

Temporary bolt for installation of an intermediate plate

PERFORMANCE ORDER
1. To establish on a camshaft a persistent ring (1) rounded off by the party forward and шпонку (2).
2. To grease bearings, a camshaft and a persistent flange.
3. Cautiously in front to insert a camshaft and to establish a persistent flange and самоконтрящиеся fixing bolts. To tighten bolts according to the inhaling moment.
4. To establish on картер directing plugs of a cover of a drive of the distributive mechanism and ring consolidations. Directing plugs are established by the rounded off ends to an external part картера in a direction of a cover of a drive of the distributive mechanism.
5. To check up, that interfaced surfaces картера and a forward intermediate plate were pure, then to put on both surfaces hermetic. Establish on картер a lining, then establish an intermediate plate.
6. To establish two central bolts and to tighten them manually, then for a while establish two more bolts. To tighten the central fixing bolts, to remove temporarily established bolts.